Drive Motor for Forklift

Forklift Drive Motor - Motor Control Centers or also called MCC's, are an assembly of one enclosed section or more, which have a common power bus principally containing motor control units. They have been used ever since the 1950's by the vehicle industry, as they utilized a lot of electric motors. Now, they are utilized in various commercial and industrial applications.

Within factory assembly for motor starter; motor control centers are quite common method. The MCC's consist of variable frequency drives, programmable controllers and metering. The MCC's are usually used in the electrical service entrance for a building. Motor control centers commonly are utilized for low voltage, 3-phase alternating current motors that vary from 230 volts to 600 volts. Medium voltage motor control centers are intended for large motors which range from 2300 volts to 15000 volts. These units make use of vacuum contractors for switching with separate compartments to be able to achieve power switching and control.

Within factory locations and area which have corrosive or dusty processing, the MCC could be installed in climate controlled separated locations. Usually the MCC will be located on the factory floor near the equipment it is controlling.

For plug-in mounting of individual motor controls, A motor control center has one or more vertical metal cabinet sections with power bus. To complete maintenance or testing, very large controllers could be bolted into place, whereas smaller controllers can be unplugged from the cabinet. Each motor controller consists of a solid state motor controller or a contractor, overload relays so as to protect the motor, circuit breaker or fuses so as to provide short-circuit protection as well as a disconnecting switch in order to isolate the motor circuit. Separate connectors enable 3-phase power to enter the controller. The motor is wired to terminals situated inside the controller. Motor control centers supply wire ways for power cables and field control.

Each motor controller in a motor control center can be specified with various alternatives. These choices comprise: extra control terminal blocks, control switches, pilot lamps, separate control transformers, as well as many types of bi-metal and solid-state overload protection relays. They also have various classes of kinds of circuit breakers and power fuses.

There are lots of options regarding delivery of MCC's to the customer. They can be delivered as an engineered assembly with interlocking wiring to a central control terminal panel board or programmable controller together with internal control. On the other hand, they can be provided ready for the customer to connect all field wiring.

Motor control centers typically sit on the floor and should have a fire-resistance rating. Fire stops can be necessary for cables that penetrate fire-rated floors and walls.

Click to Download the pdf

Forklift Parts

Parts for LPG Forklift

LPG Forklift Parts - Liquid petroleum fuel, used in heating vehicles and appliances, is a really combustible blend of hydrocarbon gases. LPG has also been increasingly used as an aerosol propellant and refrigerant. Liquefied petroleum gas or likewise referred to as LPG, is replacing chlorofluorocarbons in an effort to be able to reduce ozone layer damage. Often called autogas or...

More

---

Throttle Body for Forklift

Forklift Throttle Body - Where fuel injected engines are concerned, the throttle body is the part of the air intake system which regulates the amount of air which flows into the motor. This particular mechanism operates in response to driver accelerator pedal input in the main. Normally, the throttle body is located between the air filter box and the intake...

More

---

Gradall Forklift Part

Gradall Forklift Parts - During the time when WWII caused a shortage of laborers, the well-known Gradall excavator was established in the 1940s as the brainchild of two brothers Ray and Koop Ferwerda. The brothers faced the problems of a depleted workforce due to the war. As partners in their Cleveland, Ohio construction company known as Ferwerda-Werba-Ferwerda they lacked the...

More

---

Boom Lift Attachment

Boom Lift Attachments - Boom lifts are equipment that has a platform that can be lowered or raised to different heights, therefore making this piece of equipment an important requirement in a wide range of professions. Offered in quite a few particular varieties such as aerial hoists, scissor lifts, and knuckle boom lifts, each model operates very specifically. Aerial lifts...

More

---

Counterbalance Forklift Attachments

Counterbalance Forklift Attachments - In the material handling business counterbalance forklifts are extremely common pieces of machinery. They could be usually utilized in factories and warehouses all over the globe. The leading lift truck manufacturers such as Toyota, Mitsubishi and Linde all construct counterbalance lift trucks. They are offered in various fuel alternatives like for example diesel, electric or gas....

More

---

Carriage Rollers

Carriage Rollers - Carriage rollers are especially designed bearings that are utilized on lift masts so as to help them work in tough environmental surroundings. Lift masts are often subjected to oscillations, shocks, vibrations and high dynamic and static loads. This apparatus is frequently exposed to environmental influences like for example heat, dust, cold, moisture, contamination and aggressive ambient air....

More

---

Stacker Forklift Part

Stacker Forklift Parts - A sort of compact forklift, the electric stacker is utilized to work in smaller spaces, making loading and lifting much easier on the warehouse worker. Usually wide, but flat items like for instance slabs, tubes and pallets are transported utilizing this particular piece of machinery. There are metallic prongs jutting out horizontally from the body of...

More

---

Hyster Attachment

Hyster Attachments - As a worldwide leader in forklift trucks, Hyster always strives for excellence in product quality and safety. However, it began as a producer of lifting machines as well as winches. Most of its production was concentrated in the Pacific Northwest and dealt mostly with the wood and logging industry. A couple years after the 1st forklift trucks...

More

---